Windows 10: Various BSOD's on fresh installed win10

Hi,

Laptop ASUS UX305FA
Fresh installed system crashes every 10-15 mins with various BSODS,
Please see attached dumps and logs.

Thanks.

:)

 

OK, I'm stumped and out of ideas (Win10 crashing)

So, I've been running my desktop PC on Win10 for about 6 months now without any real issue until a few weeks ago. It started with a freeze a few minutes after logging in and progressively got worse. I looked all over the web and tried various solutions
to avoid having to reinstall everything and was losing the battle, so I downloaded the Win10 ISO from Microsoft and tried to start fresh...no luck there either. I still get various BSOD messages or just a total freeze often accompanied by a scrambled screen
(or a scrambled BSOD) and can't even make it through boot. The BSOD messages I receive are often 'IRQL_not_less_or_equal', 'memory management', 'critical process died' etc. Often I get a crash in the midst of trying to install from disc.

I have 2 3TB HDDs installed (not in a RAID config) and have run Seagate's SeaTools tests on them (both long and short tests) and they both passed. Also changed my HDD controller from RAID to AHCI in my BIOS to remove any potential Intel RST issues. I ran
memtest on my RAM and it too passed. I removed my Nvidia GPU and am now running from the onboard graphics to rule out any squirrely video driver issues. I feel like I've tested or eliminated all H/W issues except maybe a bad motherboard, and am attempting
to install a fresh copy of Win10 from disc onto a freshly formatted HDD and am still getting crashes.

Does anyone have any suggestions? Because I'm all out of ideas...

 

Crashes and BSOD Fresh Win10 Install

Thanks. Before seeing your reply, I was able to keep the system on long enough to install updates. (Crashed while downloading them, but was able to finish downloading them after reboot.) After installing updates the system ran fine for 3 hours. Will update
later if I experience any more issues.

 

Hi Boris Byzov *Smile

Welcome to the 10forums.

I've gone through the event logs a bit, of the 17 dumps that are present at least 11 are memory related.
For this reason, please follow below instructions to run MemTest86+ to test your memory.






Diagnostic Test

RAM TEST


Run MemTest86+ - Test RAM - Windows 10 Forums



Note



MemTest86+ needs to be run for at least 8 complete passes for conclusive results. Set it running before you go to bed and leave it overnight. We're looking for zero errors here. Even a single error will indicate RAM failure.
Addition:
If errors show up you can stop the test, remove all sticks but 1 and test this single stick in each slot for 8 passes or until errors show, switch sticks and repeat.
If errors show up and you see them a lot later, no problem, the errors don't affect the test.

 

Good morning,
I did memtest this night, there was no errors.

 

Lets test the drivers, please note that there may be more than 1 driver causing problems if any is causing problems.





Diagnostic Test

DRIVER VERIFIER


Warning Please make a backup of your important files and get your rescue media or create one.
Please create a restore point.
Please follow this tutorial to run driver verifier.

Driver verifier stresses your drivers and will crash your pc if any driver fails due to a violation.

Driver verifier should be performed for a max of 48 hours, or when you have a bluescreen, whatever comes first.

If driver verifier has found a violation and you can't get back into windows normally, try to boot into safe mode and reset in safe mode driver verifier, or in the troubleshooting options open command prompt and type verifier /reset.



Note Your system will act very sluggishly while driver verifier is enabled, this is normal as your drivers will be being subjected to heavy testing in order to make them crash.

Please fill in your system specsPlease follow this tutorial and download the tool. The tool will give you detailed information about your system specs, please fill in your system specs more completely.How to fill in your system specs: